19.10.12

About Two-Bath and Highly-Diluted Developers



First, I must confess: I developed only one batch of films several years ago with a two-bath developer. After that I didn't use them for the simple reason I overstocked much of the BW chemistry in the darkroom (conventional developers), so I needed to get rid of that chemistry first...and it takes some years to do so. But I just decided to give them a go again, to these simple but excellent developers, in the following weeks.

Two-bath developers have been very popular in the past; their use never stopped, but in the past decades only a limited number of photographers were consistently using them. There are really many formulas around, but basically the first bath is only a solution of the active agent (metol, hydroquinone, catechol etc.) and a preservative (sulfite), while the second is just an alkali bath (usually NaOH) . When we first soak the film in the first solution, the film emulsion absorbs the active developing agent but the development hasn't started yet. Then, when we switch to the second bath (with just little agitation), the development starts because of the alkaline pH. The development in more exposed (denser) areas of the negative is of course quicker, but it also stops (or slows down) faster because the developing agent is more quickly exhausted. Inversely, the development in less exposed areas goes on for a longer period, and these areas gain more density relatively to their exposure. In other words, two-bath developers are highly compensating; they produce a usable negative (almost) regardless whether the photographic scene was of low or high contrast. Very usable for roll films (less for sheet film where you strive to have complete control) where many different shots are made on a single roll. Given the increased density of shadow areas, they are regarded as speed-increasing developers, at least some of them. A nice feature is also about the developing times (of individual baths) and temperatures; they are very little affected by, since the development is mostly governed by developing agent exhaustion. Similarly, using the same approach with different films produces good or at least usable negatives. Two-bath developers are also very economical; the first bath virtually lasts as long as there's any solution to soak the film (well it's still better to change it a bit more frequently), while the second solution can be prepared fresh, since its cost is neglible.
Highly diluted developers (the most known is surely Rodinal, like 1:200) are also known for their compensating effects, but in that case the main driving force is diffusion-that is, temperature plays a bigger role in the development, as also the (low rate of) agitation technique. Because of that, using highly diluted developers is more likely to produce unevenly developed negatives (because of low agitation rates). Also, the long development times required (like 1-2 hours) inevitably produce more grainy negatives. However, highly diluted developers are quite good in producing the »edge effect« in negatives, enhancing the apparent sharpness of the image. On the other side, developing in highly diluted developers reportedly produces image that are somehow »dull«-uninteresting in mid-density areas. But this is also a matter of taste.

Below are some of the most known two-bath formulas:

Pextral 2-bath:
Bath A
1.5 g Pyrocatechol
0.3 g sodium sulfite
Water to 300 mL

Bath B
6 g sodium hydroxide
Water to make 300 mL

This is a staining developer, as other pyro-type developers, acting also as a gelatin hardener. 
2 minutes in bath A, 1 minute in bath B. Use this as a starting point only.


Divided D-23 developer (used also by Ansel Adams):
Bath A
100 g sodium sulfite
7.5 g metol
Water to 1 L
Bath B
2 g borax
Water to 1 L


Barry Thornton formula
Bath A
80 g sodium sulfite
6.5 g metol
Water to 1 L

Bath B
12 g sodium metaborate (Kodalk)
Water to 1 L


The last formula is apparently just a slight variation of the divided D-23, but it usually somehow gives more »energetic« negatives, since the second bath is more alkaline, therefore more active development occurs. It's been also one of the most regarded contemporary two-bath developers. For both of these developers, 4-5 mins in each bath are a good starting point.

A note about modern films: early films used to have a much thicker emulsion layer, therefore they absorbed more of the solution A. Modern films, especially films with tabular crystal structure (Tmax, Delta, Acros) have a much thinner emulsion layer. In case you find the negatives to be too »thin« (underdeveloped), a good way to improve the negative density (and contrast, while still getting consistent results) is to increase the concentration of the developing agent in bath A to allow more active development (keeping the sulfite concentration unaltered). 
The widespread use of thin-emulsion films was one on the main reasons why the use of two-bath developers vanished.

1 comment:

  1. very interesting post. I would try to get sth. prepared FOR me (e.g.) manufactured, because of lack of a dedicated workroom (e.g. wet darkroom). I do use a two-bath developer but technically it#s different from the one you mention here. The first bath „prepares“ the exposed silver in the emulsion for the developer doing its work. Information is in German, only, unfortunately: http://www.spuersinn-shop.de/index.php?page=product&info=397

    Recent Example (ETRSi, Tri-X 400) http://rlfsoso.tumblr.com/post/33853302761/portrait-of-robert-october-2012-on-flickr-this

    ReplyDelete